You can switch to any other flash drive if you have. If the LED of your flash drive is still blinking, then it is working but the speed is slow! But if it has not blinked for the last 40 seconds, your Wii needs a reset. Sometimes, for the first time, this method does not work out. But in second or third time, it gives successful results. Q: The ripping of disk freezes either at 0.
A: You can try to reinstall the IOS file or clean your disk. But if you have a hard modded Wii, this solution will not work for you. A: It may be possible that you have a lightly scratched DVD or not an original one but a backup copy. First clean the DVD and try again. If still it does not work, then you can burn another copy. A: First connect your USB drive. Now, Right click on the name of your device and create a new partition or format the whole drive.
Q: What is WTF? Press any button when prompted. This will exit the setup and return you to the Homebrew menu. Part 5. It's in the middle of the Homebrew menu. The installer window menu will open.
Scroll left to the "IOS" option. This will select the IOS file that you installed earlier. Press A. Doing so confirms your choice.
Agree to the terms of use. Press A on your controller to agree to the terms of use. Select an IOS version. Select a custom IOS slot.
Select a network installation. Press Left until you see "Network installation" appear between the brackets. Start the installation. Press A to begin installing the IOS installer. This will move you to the next part of the installation.
Select another IOS version. Select another slot. Use the network installer. Select "Network installation" and press A as you did with the last installer, then wait for the installation to complete. Press any button when prompted, then press the B button.
This will restart your Wii. When it finishes restarting, you'll be able to proceed. Part 6. Navigate to the next page over. Press the Right arrow on your Wii remote's D-pad to do so. Select WAD Manager. It's the second option on this page. Doing so will start up the WAD Manager installer. This agrees to the terms of use. Select "IOS" to load. Disable the emulator. Select "Disable" in between the brackets and press A. Select your SD card. Doing so brings up a list of the files on the SD card that you inserted earlier.
Scroll down and select WAD. It's near the bottom of the screen. Select the USB loader. Install the WAD Manager. Press A when prompted to do so. This will restart the Wii. Once the Wii finishes restarting, you'll be back on the second page of the Homebrew channel.
Part 7. It's on the Wii remote. Pressing it brings up the Home menu. Select Shutdown. It's at the bottom of the menu.
Your Wii will power down. It's best to wait until your Wii fully powers down before proceeding. Insert your flash drive into the Wii. The flash drive should plug into a USB port at the back of the Wii. Turn back on your Wii. Press your Wii's power button to do so. It's on the right side of the page. Select Start. This process will take several minutes, especially the first time you run the program.
Insert a game. Place in the Wii the disc for a game that you want to back up to the USB flash drive. Select Install when prompted. The program will begin reading the contents of the disc. Select OK when prompted. Doing so will prompt your Wii to begin burning the disc onto the USB flash drive. This process will take quite some time, and the burning progress bar may appear to freeze at multiple points. Do not remove your USB drive or restart your Wii if this happens.
This will complete the burning process. At this point, you can eject the game disc from the Wii. Play your game. Click the game's name, then click the spinning disc icon in the middle of the window. This will launch the game. If the Wii is stuck on the black screen, your console may have crashed. If you cannot force a shutdown, the only way is to unplug the Wii's power. If the screen goes black and returns to the Wii menu, you'll need to install a cIOS. Not Helpful 4 Helpful Yes, you should skip that step as you already hacked it and already can install homebrew apps.
Not Helpful 2 Helpful 9. Not Helpful 9 Helpful 6. Is it necessary that I format the SD card after installing the homebrew channel? After homebew is installed, you only need to delete the files on your SD card. Formatting the card is not required. Not Helpful 4 Helpful 9. Unfortunately, that's not possible. Not Helpful 54 Helpful The image of the installed game worked, and I thought the gameplay worked, but it didn't it always send me back to the Wii menu.
Milos Tosic. Did you try to load another game? It may be because the WBFS for that game is broken. Not Helpful 3 Helpful 4. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article Steps. Tips and Warnings.
Things You'll Need. Related Articles. Author Info Last Updated: June 3, Get an SD Card. Insert it into your computer through a built-in slot or a USB card reader. Open the zip file and extract installer. Rename it to boot. Make sure the design is facing to the right to avoid getting it stuck, in which case you will need pliers.
It should pop up "Load boot. If it freezes, and you followed the directions exactly, try a different version of Bannerbomb. Include your email address to get a message when this question is answered. Helpful 0 Not Helpful 0.
0コメント